|
|
|
| Made with Pride in the - - Picture Gallery - -
Features: Transfer pick and place part loader, high speed precision ball travel set station, auto roll pin install, auto spring install, roll pin press, reject unload and good part unload. Runs at a 5 second part to part cycle time.
90 Degree Glass Transfer Conveyor
Features: Automatic glass size adjustment, Variable speed conveyor. Features: Glass tape wet out press, vision system for text identification, runs left and right hand with fixture change, heater pad check, glass orientation check, auto unload and convey back to operator. Also built on our new heavy duty electric lift workstation.
Features: Runs left and right hand without nest change, checks pre-stake boss
height, check finished stake height, checks for studs checks for connector.
Features: Dual vision camera system, glass curvature detection, heater pad
detection, motor current draw, mirror travel, good part marking. Also built on
our new heavy duty electric lift workstation. Features: Runs left hand and right hand with no changeover, Auto lock when part is properly loaded in fixture. Also built on our new heavy duty electric lift workstation.
Features: Two assembly stations, one end of line
tester, ergonomic workstations and required material handling equipment.
P221 Ford F-150 Floor Shifter - Environmental cycle tester. Features: Tests two shifters per unit, Monitors shift
position, Monitors Shift effort, Actuates shift button, Monitors shift button
effort, BTSI solenoid actuator, electrical system test and Fully
Programmable.
P221 Ford F-150 Floor Shifter - High Speed Environmental Cycle Tester Features: Cycle tests three shifter simultaneously,
Fully Programmable.
Features: Shift position actuator with force and
position feedback, Side load actuator and fully programmable.
Features: Part mounts on the three datum's, Part presence
verification and Screws are driven with torque clutch monitoring.
U-222 Ford / Lincoln side mirror - assembly machine. Features: Set up to run both left hand and right hand
assemblies simultaneously or independently, Four position index
table, first position - operator load, second position - heat stake six points,
third position - drive three studs in both left and right hand parts, studs are
bowl fed and driven using a servo driven X-Y system positioning a D.C. electric
driver with torque and angle feedback, fourth position - good part unload.
Features: Four position
index table, first position - operator load, second position - drive 3 studs in
both left and right hand parts, studs are driven using a servo driven X-Y
positioning a D.C. electric driver with torque and angle feedback, third
position - reject unload, fourth position - good part unload. Features: Set up to run four different transmission
valves, Precision probe assembly for ball travel measurement, Stepper driven
linear actuator for ball travel setting, reject unload with lock box, 6
second part to part cycle time and ergonomic workstation.
2003 Chrysler CS exterior side mirror bracket - stud drive machine. Features: Bowl fed studs with torque and angle feedback
drivers, runs both left hand and right hand brackets simultaneously or
independently.
U222 Power fold - assembly station. Features: Screw driver with torque and angle feedback,
90 degree part flip, Power fold motor rotation and wiring test and ergonomic
workstation.
Features: Shuttle parts in and out of six independent
test stands, Pallets with RF tags for part status, two pin stamp marking
stations, two good part unload stations with part type sorting, two reject
unload stations, etc...
Features: Pivot pin press station with press force monitoring, retaining clip press with clip orientation detection, rooster comb auto grease application and ergonomic workstation.
Features: We have put together the best workstation available today. Our standard workstation has a 13 inch electric lift system, is rated to lift 3500 pounds and optionally can be ordered with a 5000 pound lift system. We can customize our workstations to fit your specific needs. Our workstations are designed and built with safety in mind. For more information, follow the link above.
Ergonomic Workstation
Brochure
Features: We can completely customize our ergonomic workstations to suit your specific applications. These tables can be built up to weigh as much as 1000lbs.
Ergonomic Workstation
Brochure
Features: We can completely customize our stands to suit your specific applications. I.E. Quantity and location of: Shelves, Printer drawers, Keyboard drawer, Date stamp units, etc....
Custom Made Connector blocks Features: Connector retaining latch, Pogo Pin connection, Amphenol quick change coupling, Pin prick for part identification.
|
|
Home
Types of Equipment
Services
Picture Gallery
Workstation Tables
Engineering Tools
Contact Us |
